Clutch gone after trip abroad- now fixed and back on the the road

Discussion in 'Mech Tech' started by 1973daisey, Jun 5, 2017.

Page 2 of 3
  1. art b

    art b

    That may put the bride off
     
    art b, Jun 6, 2017
    #21
    1973daisey likes this.
  2. 1973daisey

    1973daisey

    Right bride left 5:35 booked then changed cloths and got the little bigger the I'll the needle bearing that holds the the input shaft fell to bits that be the bigger u think clutch got loads of meat on it so hope it's just this little roller bearing £3 job just gotta press it in flywheel grease it up better and should be good to go [​IMG][​IMG][​IMG][​IMG][​IMG]


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #22
    Spacecowboyuk, womball, Merlin Cat and 1 other person like this.
  3. 1973daisey

    1973daisey

    @Flakey can u bell me please mate lost ur number 07878177234


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #23
  4. Merlin Cat

    Merlin Cat Moderator

    Good luck si :)
     
    Merlin Cat, Jun 6, 2017
    #24
    1973daisey likes this.
  5. 3901mick

    3901mick

    Doesn't the bearing go into the crank ?
     
    3901mick, Jun 6, 2017
    #25
    1973daisey likes this.
  6. 1973daisey

    1973daisey

    A quick call to a pall at muscle bus and he is on his way over with a locking tool and rattle gun ....


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #26
    womball likes this.
  7. MorkC68

    MorkC68 Administrator

    yes it does if your running a six rib box.

    However, the new needle roller bearings are T25 ones (from VWH) so you have to counter bore the flywheel to enable the bearing to fit correctly :)

    (Ive just been back through what we did to check for you)
     
    MorkC68, Jun 6, 2017
    #27
    1973daisey likes this.
  8. 1973daisey

    1973daisey

    Yes it was bored out fits snug I don't remember ever greased this bearing only few £ fly wheel off with pals rattle gun and bearing is out shall buy new 1 Tomoz GREASE it and press it in and torque up fly wheel with new locking plate I have ! Whop it back in and go camping the weekend


    Sent from my iPhone using Tapatalk[​IMG][​IMG][​IMG]

    This is the culprit!!
     
    1973daisey, Jun 6, 2017
    #28
    nicktuft, Lasty, womball and 1 other person like this.
  9. 1973daisey

    1973daisey

    Yes but I'm type 4 with a 1600 box so input shaft is shorter mate so it's pressed into flywheel been sweet for 28,000 miles this way !


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #29
    davidoft and 3901mick like this.
  10. paradox

    paradox

    There's never any moss going to grow on you mate
     
    paradox, Jun 6, 2017
    #30
    art b and 1973daisey like this.
  11. 1973daisey

    1973daisey

    No chance I gotta get back out camping the weekend mate hope to have it done by Thursday as I go out Wednesday nights on the calling


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #31
    Jack Tatty, Lasty and 3901mick like this.
  12. MorkC68

    MorkC68 Administrator

    :thumbsup:

    You know this anyway, clean up and burrs with emery paper before you refit everything, make sure there are no rough/sharp edges :)

    hope its sorted matey!
     
    MorkC68, Jun 6, 2017
    #32
    1973daisey likes this.
  13. 1973daisey

    1973daisey

    Have cleaned it all up with 2000 grit all ready got all the old 1 out and cleaned up the engine of muck ect


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #33
    MorkC68 and Flakey like this.
  14. art b

    art b

    It's like an F1 pit stop ....:cool:
     
    art b, Jun 6, 2017
    #34
    scrooge95, Jack Tatty and 1973daisey like this.
  15. Spacecowboyuk

    Spacecowboyuk

    Lucky this happened at the end of the trip. Good save:thumbsup:
     
    Spacecowboyuk, Jun 6, 2017
    #35
    1973daisey and art b like this.
  16. 1973daisey

    1973daisey

    It's no different to what iv always been art if it's broken........fix it ☝️


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #36
    womball likes this.
  17. 1973daisey

    1973daisey

    Very lucky !! Camping near u the weekend kid that place in fenal Heath on the 449 with brad and few palls of his on sat night


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 6, 2017
    #37
  18. Spacecowboyuk

    Spacecowboyuk

    Sweet dude. Can't think where that is in FH though? I may take a drive out and grab a beer with you - the missus still hasn't experienced the joy that is the bay
     
    Spacecowboyuk, Jun 6, 2017
    #38
    1973daisey likes this.
  19. 1973daisey

    1973daisey

    [​IMG]
    B there from 4 ish after been to Gloucester jump tastic for his birthday



    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 7, 2017
    #39
    Spacecowboyuk likes this.
  20. 1973daisey

    1973daisey

    New part on board ready to refit after work !! Looks much better quality!!! [​IMG]


    Sent from my iPhone using Tapatalk
     
    1973daisey, Jun 7, 2017
    #40
    Flakey and womball like this.
Page 2 of 3

Share This Page