FOR SALE Selection of Type 4 tinware

I've a selection of type 4 tinware for sale.

All could use a clean up and repaint.

Price is £12 + postage a piece.

First up is some bits for the 75-78 US style exhaust/HE set up:



The rest is I think for any type 4.







Top covers aren't in brilliant condition (one corner rusted badly as can be seen in second picture), but should clean up OK.
These are £12 each + postage, or £20 for the pair.



Finally, not totally sure what year this is for. I "think" it's a right side heat tube between snail fan and heat exchanger, however it didn't fit when I recently fit my 72-74 style heat exchangers as the bend isn't right to get round the alternator. Someone might be able to tell us what year it's for or where it's for if I'm wrong about it! It was in a box of bits from a 79 FI engine so perhaps it's for the '79 style square port HX's??



Can be collected from Kidlington, Oxford, or will post at cost.

Thanks.

 

Also an under tin from the standard european (72/74 & 79) set up.

This one however has rusted away in one section and so would need patching.

£8+postage.



Thanks.

 

have you got the left side under tin?
thanks

 

What year/style are you after? I have the one in the first picture for a 75-78 US set up.

 

mines a uk model cj code

 

Sorry, don't think I can help you as UK ones never had the tins I've got.

@Paul Weeding makes GRP reproduction ones that would fit - see the first post on the classified parts page.

 

Hi, have you still got the top left tin and the bottom right one please?

 

Hi @ghiahead. Do you mean top left, bottom right with respect to position on van or my first photo?

If photo (the two hear riser tubes specific to 75-78 US) then yes I still have them.

Nick.

 

Hi Nick, sorry to confuse, I ment the position on the van the top left tin that covers 3 and 4 cylinders and the bottom right push rod cover, the left one on your photo.

Ken

 

Hey, have you still got the two large flat panels in the top picture in the centre?

Cheers,

 

In desperate need of the bit on the left of picture 2. Let me know if it's still available mate. mattnorris@hotmail.co.uk

 

Nick,
How much of this is left?
I need a couple of bits for Bill and Ted.

 

@Matt Norris - yes I think I still have that bit but will go and check to make sure once the kids are in bed. Its the rear middle bit you were after right?

Glynn - I have most of it still, however most of it is for the US 75-78 exhaust/HX set up and so not sure if any of it will be any use to you. Which bits is it you need?

 

Yes please. Let me know how you want to be paid fella.

 

@Matt Norris - have looked and do indeed have it still. Will PM you.

 

Hi pea soup are the top photo ones off a 2ltr ? if so i will take the 2 heat riser pipes, in the top photo please. how much posted to dh89en

cheers

 

@westy1 - yes they are off a 2ltr. I'll dig them out tomorrow and weigh them to come up with a postage cost. Just to confirm, its the two heat pipes that go up to the heater control flap pods that you want?

 

Hi Nick, I'm still wanting a top left tin that covers 3 and 4 cylinders if you still have it.

Ken

 

Hi @ghiahead - sorry, thought I'd sent you a PM about that but can't see it in my sent messages list - sorry

Yes, still have the top cover. Needs a clean up and an paint, but other than that is very solid.

I'll measure/weigh it tonight to get a postage cost for you.

Nick...

 

Thank you.