Erbaspatcher ba6 fitting from scratch (with some help from Tlb )

Discussion in 'How To' started by 1973daisey, Oct 31, 2015.

  1. Zed

    Zed Gradually getting grumpier

    So crude. lol
     
    1973daisey likes this.
  2. What u mean ste ?
     
  3. Zed

    Zed Gradually getting grumpier

    All the points and glowy bits.
    I remember being shocked at find my ex-moggie minor fuel pump had sparky points inside it.
     
    1973daisey likes this.
  4. I no but it all works now and easy to fix
     
  5. PSG

    PSG

    @zed just turned his on in his early. and it worked. he is lucky lol. the knob has broken off my switch so i need to work out how to turn the thing on to try it. Take it the engine has to be running. Do you just have to turn the knob til it clicks? like a thermostat kind of click?
     
    1973daisey likes this.
  6. Zed

    Zed Gradually getting grumpier

    I did, I got lucky, but these underfloor ones are better.
     
    1973daisey likes this.
  7. davidoft

    davidoft Sponsor

    Have you got a green knob on the dash ?
     
    1973daisey likes this.
  8. Looking how mine works it's really basic !!
     
  9. PSG

    PSG

    it has snapped off. but i can turn the shaft part of it.
     
  10. davidoft

    davidoft Sponsor

    You need to put your dash heater controls to hot ( down) and turn the knob clockwise to adjust the heat, if you push it in and turn it's a 10 minute clockwork timer, if nothing happens check under the dash on the left above the fuse box there's a little black box with a red reset lever try that, then there's other stuff, check the fuses too
     
  11. davidoft

    davidoft Sponsor

    Luckily it's veeerrryyy basic ;)
     
    1973daisey likes this.
  12. Had a good few hours today got it up and running today was quite shocked at how hot it kicked out the heat !!
    Then filled the holes cleaned and rust treated it vht painted it and tested it all again to cure to paint !! Then cut the main Pipe out the bus and made some joining pipes !! And had to move the clutch tube I fitted when I converted it to manual as it was in the way !! Then test fit it to make sure it actually fitted in and can get the belly pan on ...... And yes it does so now just need to make an inlet (into the main pipe) for the blower fan as this bits missing and then I can fit the wiring loom and switch and then start fitting the components fuel pump /fan exhaust ect but had a good day well chuffed it all works now !! Cheers @davidoft for the phone call explaining how it all should go !!
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
    Lord Congi, davidoft and zed like this.
  13. davidoft

    davidoft Sponsor

  14. I have to put a co2 meter infringement of it 1st lol u no what's she is like
     
    davidoft likes this.
  15. Zed

    Zed Gradually getting grumpier

    Nice and quiet then. :D
     
    1973daisey likes this.
  16. It's on a hollow aluminium rail bud but it's not to bad !! I'll be toasty warm do not bothered about the noise !!
     
    Lord Congi and PSG like this.
  17. Zed

    Zed Gradually getting grumpier

    I've had my arm twisted to get a silencer for mine.
     
    1973daisey likes this.
  18. Please explain this to me in Daisy terms !!
     
  19. Zed

    Zed Gradually getting grumpier

Share This Page