Another ej20 thread

Discussion in 'Modified Shizzle' started by jimmy1975t2, Aug 29, 2014.

  1. Pictures say a thousand words apparently ;)

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
  2. cool looks like your well under way...:hattip:
     
  3. Quick question for the dunce over here, what happens between engine and chassis? As the gap is filled neatly with a foam seal on original engines.
     
  4. Flakey

    Flakey Supporter

    It's water cooled, it doesn't need to have the top and bottom halves of the engine separated for cooling purposes!
     
    jimmy1975t2 and Paul Weeding like this.
  5. As flakey has said, I don't need to worry about that as there isn't a hot and cold side of the new engine unlike the old aircooled engine. The main issue with the subaru conversion is that the engine does hang low in the chassis so ground clearance is an issue with a lowered bus

    ImageUploadedByTapatalk1410732531.076863.jpg

    As you can see from that photo
     
  6. kev

    kev

    how do you remove the engine if you have welded the engine bracket in place
     
  7. I wanted to make it removable but it turns out it doesn't need to be. The bracket sits inline with the gearbox. To remove the engine I release the engine mounts from the bar jack the engine up, remove the mounts from the engine, then the engine pulls forward and down just like removing the standard aircooled engine. There is loads of space inside the engine bay but to give that bit more I have made the engine bay trims removable
     
  8. Baysearcher

    Baysearcher [secret moderator]

    Is that sump shortened?
     
  9. Yes. I cut the sump down and welded a sheet of 2mm steel on it at a slight angle and made a section for the drain plug. I just need to shorten the oil pick up now
     
    Baysearcher likes this.
  10. ImageUploadedByTapatalk1412011734.240042.jpg

    ImageUploadedByTapatalk1412011764.556748.jpg
     
    NewtoVW likes this.
  11. kev

    kev

    Is your sump shortened
     
  12. Baysearcher

    Baysearcher [secret moderator]

    Yep
     
  13. Looking good mate, i know what you mean about ground clearance, will have to put off slamming the T25 till i'll get my sump shortened
     
  14. Cheers. On a t25 its not too bad as they are higher and the engine sits higher in the chassis. A friend has just put a ej20 quad cam (170bhp) from a jap import legacy into his wedge and he has no issues with clearance at all.

    Cutting the sump down and shortening it was the easy part, I've not got to work out how long the strainer needs to be for the oil pick up and get that sorted
     
  15. Made a start on the manifold tonight

    ImageUploadedByTapatalk1413844859.528168.jpg

    ImageUploadedByTapatalk1413844866.344996.jpg
     

    Attached Files:

    art b likes this.
  16. Mock up complete

    ImageUploadedByTapatalk1414782081.529681.jpg
     
    Spacecowboyuk and NewtoVW like this.
  17. @jimmy1975t2
    A good thread this.. Helps me a lot.. Come back and finish it please.. I need input :thumbsup:


    With lots of pictures :D please.
     
  18. You'll get a nice burble off that pipe with the different length headers!
     

  19. Hey guys, no this isn't finished yet. The aim was to use my bus as my wedding car next weekend, but unfortunately me and my fiancé split up earlier in the year so I have since taken a break from working on the bus but shall be getting back on with it again soon. A few of the plans and ideas have changed now so watch this space
     
    Paul Weeding likes this.

Share This Page