Here is what I have so far

Discussion in 'Modified Shizzle' started by Ian Jones, Nov 8, 2020.

  1. Here is what I have so far for my Subaru swap feel free to add anything that you think I should be looking at and or changing.

    Engine
    177BC48F-7832-4A4A-AEF5-D77D8F395F7A.jpeg

    Loom
    17D09061-9AED-46A3-87B5-8AF1CB275D27.jpeg

    Shortened sump

    28BCD3DA-29DE-483D-8F09-0488F1E36EA6.jpeg

    Radiator and fans

    D7EE135A-666D-4867-BCA8-F5F3BE8E62F7.jpeg

    I’ve spoken to Nick Tune about a bracket for the alternator relocation as the inlet manifold has been reversed so hope he will sort that for me this week. So I have the internal heater, rad hoses, brackets to mount the rad, gearbox bellhousing adaptor, and engine support bar to get anything else I should add to my list thanks for any advice Ian
     
    jason sanderson likes this.
  2. Oh and exhaust nearly forgot that lol
     
  3. Fuel pump and air filter
    :thumbsup:
     
    Ian Jones likes this.
  4. @Razzyh @pkrboo when you say you used T25 pipes for the radiator on your Subaru conversion I assume the long ones that go right to the front ? And you said you used straight pipes and bends on the last one Matt which worked out better thanks.
     
  5. Razzyh

    Razzyh Supporter

    Yes t25 pipes cut up to fit. Using silicon hoses to join where required.
     
  6. What rad setup are you using
     
  7. I’m not sure where they are from but look very similar to the Fellows one
     
  8. I am thinking of building my own rad scoop as we have a sheet metal firm we use at work and he says he can make me one very cheaply ;) if I give him a drawing to work too
     
  9. The rad I have is in a scoop

    DBEB4226-3073-4FBC-BB92-EA8C4B4C41D5.jpeg
     
  10. That look about what I was aiming for
    I think landrover/ rangerover rad s are what people tend to use with aftermarket fans
     
  11. Ok picked up an exhaust today off the same guy who wanted my 1500cc beetle engine so swap and a bit of cash his way I’m really happy with that. 2F068BF8-B9AB-4601-B8EF-0A16594FDD4A.jpeg
     
    pkrboo, just-paul and lowie like this.
  12. Nice find that
     
  13. Yeh it owes me £300 so I thinks it’s a good deal but may need to have another sensor port fitting to it as my engine has 2 sensors.
     
    Razzyh likes this.
  14. Thanks to @just-paul i now have a couple of T25 water pipes and an Aluminium header tank. Just need @Razzyh or @pkrboo to tell me how they got a bead on the end of them :)
     
  15. Razzyh

    Razzyh Supporter

    Cut them to length and then warm the ends up and push down on a piece of wood to give it the lip. Can do a video tomorrow if you want.
     
  16. Razzyh

    Razzyh Supporter

    Which one you got?
     
  17. Exhaust ? There is a picture of it higher up
     
  18. If you c
    If you could that would be great.
     
  19. Razzyh

    Razzyh Supporter

    Do you need to get another lamba sensor fitted?

    Right by the exhaust outlet.
     
  20. Razzyh

    Razzyh Supporter

    I need to read everything before replying

    Subscribed now.
     

Share This Page