Thermostat repair

Discussion in 'How To' started by Barry Haynes, Jun 12, 2020.

  1. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    As I was doing another one I thought I would do a how to this is the same procedure for any air-cooled thermostat

    (1) with a small hobby torch heat up the end of the thermostat that has the thread on and the end will come off, take a cotton cloth and while it is still warm wipe off the solder and clean the surfaces
    (2) the threaded bit is hollow heat this up and remove the solder
    (3) next take some flux paste and apply to both surfaces now clamp the thermostat in a vice and heat
    (4)now you need to take a syringe and add 2 ml of 99% isopropyl alcohol through the threaded tube
    (5) with the thermostat still in the vice carefully heat the threaded piece and seal with solder
    (6) job done test to see it it opens on the stove

    A type 4 thermostat opens at 85° and isopropyl alcohol opens at 82 ish so close, I've now done 3 and none have failed


    [​IMG][​IMG][​IMG][​IMG][​IMG]

    Sent from my Pixel 3 XL using Tapatalk
     
  2. Faust

    Faust Supporter

    Think you need to get the Brasso out now Baz for the final topping .
     
  3. Where did the original alcohol go?
     
  4. Zed

    Zed Gradually getting grumpier

    What!!!

    I've just bought a new one from the US and I'm embarrassed to say how much it cost in total.

    If I send you my old one can you fix it for me to have as a spare?
     
  5. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    If I can do it you professionals will ******* it:thumbsup:
     
    Betty the Bay likes this.
  6. Zed

    Zed Gradually getting grumpier

    Good question.
     
  7. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    when they fail there is a hole somewhere so there, and also when you heat it up it will burn off, of the 3 I've done all were dry inside
     
    paradox likes this.
  8. Faust

    Faust Supporter

    Filled with London Pride .
     
    CollyP and Barry Haynes like this.
  9. Baz drunk it.
     
    Barry Haynes likes this.
  10. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    Found it, here is what I followed
    Screenshot_20200612-180723.png
     
    DubCat and paradox like this.
  11. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    Like it like it Rodney
     
    Faust likes this.
  12. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    Gingerbus, snotty and CollyP like this.
  13. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    I just had a re think this only applies to T4 thermostats because the isopropyl alcohol has a boiling point of 82, for a T 1 you will have to search the net for the correct alcohol
     
    JamesLey likes this.
  14. mcswiggs

    mcswiggs Supporter

    I love it when the unfixable becomes fixable. Gives me one less thing to worry about. Great skills btw.
     
    snotty likes this.
  15. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    Why thank you,
    The only problem I can see is when the bellows are damaged but Ratwell say that the majority of leaks are where they are soldered
     
    paradox likes this.
  16. You did that “How to do a white-eared elephant”, but that got deleted.
     
    Soggz, Gingerbus, Lasty and 2 others like this.
  17. Chrisd

    Chrisd Supporter

    Nicely done. I managed to fix mine after many attempts but I did not seem to have the hole in the side thread or I missed it! I filled from the end of the threaded bolt and that caused me my issues with the alcohol stopping the solder fixing.
     
    mcswiggs and Barry Haynes like this.
  18. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    There is a hole at the side at the bottom of the thread fill this first which should stop the alcohol them fill the top with solder, well done by the way:thumbsup:
     
    Chrisd likes this.
  19. I always presumed they failed because they had split and thought soldering them up wouldn’t last
    I didn’t realise most failed because the solder failed
     
  20. Barry Haynes

    Barry Haynes I dance in leopard skin mankini’s

    I've read many articles on this what is said time after time that the solder is the weakest part and most fail there
     
    Valveandy, paradox and JamesLey like this.

Share This Page