The elite posh single/double cab section

Discussion in 'Show Us Your Ride' started by dog, Oct 11, 2013.

  1. So on doka they would be at back of the extended under seat storage area?
     
  2. Flakey

    Flakey Sponsor

    I imagine so yes, never having stuck my head in one of them :)
     
    Bertie the Bus likes this.
  3. they are bolted on ,you should see the holes..
     
    Bertie the Bus likes this.
  4. What, captive nuts in them? I will have a look later.
     
  5. Flakey

    Flakey Sponsor

    This is what a single cab looks like from the locker through to tank area, those panels bolt here you can see captive nuts
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    Ps, it looks a bit nicer than that now
     
    Bertie the Bus likes this.
  6. Hi,

    For a doka the firewall is in the same position as a pick up, see below picture of the firewall shields installed:

    [​IMG]

    Best regards Richard
     
    GONA66, Phooey, Flakey and 1 other person like this.
  7. Thanks Richard that is excellent and just what I needed. We have gone ahead and purchased a pair.
    Your picture sort of answers another question that raised itself when I was looking at my daughters doka this morning. The beam across the back of the cab has a large hole and I was wondering why but I see you have a plastic cowl thingy over the hole. Tell me more! Is it some sort of heating channel? Are the plastic cowls available new - what are they called?
    Many thanks
     
  8. Flakey

    Flakey Sponsor

    It's part of a air intake system from the little louvres on the cab rear pillar to the air filter in the engine bay via the large load bed support member, again same as single cab, little plastic bit I imagine is rocking horse poo rare!
     
    Bertie the Bus likes this.
  9. Hi,

    Flakey was faster, only to add to the very complete response see picture with the full part. I do not know if/ where this can be ordered new. I think you will need some luck to find this item.

    [​IMG]

    Br Richard
     
    Bertie the Bus and Flakey like this.
  10. Cheers guys - great info:)
    I guess we will end up trying to fabricate some alternative to the plastic bits when we get to that stage:(
    If you happen to see the bits anywhere please give us a heads up :thumbsup:
     
    Flakey likes this.
  11. Flakey

    Flakey Sponsor

    I'll point out it only works if you have stock air filter with a tube to the corresponding hole in the rhs of the beam in the engine bay
     
  12. seems a bit elaborate. Why so different to a bus?
     
  13. Flakey

    Flakey Sponsor

    I guess because they don't have two big forward scooping vents in the rear corners, the louvres in the lower side panels don't vent into the same place
     
    Bertie the Bus likes this.
  14. Mmm, I guess so!
     
  15. Flakey

    Flakey Sponsor

    Bertie the Bus, DOKA '73 and GONA66 like this.
  16. Thanks for the link
     
    Flakey likes this.
  17. paradox, Flakey and Bertie the Bus like this.
  18. no but thinking of trying it out. the side windows are the same measurements as split pop outs so should be doable!
     
    72crewdude likes this.
  19. Can somebody measure from the base of the seats to the first bolt on the gearstick Svp



    [​IMG]

    @Flakey :D

    Sent from my iPhone using Tapatalk
     
    Last edited: Mar 15, 2017

Share This Page