New interior for Ollie

Discussion in 'Mech Tech' started by mgbman, Oct 24, 2019.

  1. Had my converted panel van over 5 years now and its time to spruce up the interior as a little winter project for me.

    The old homemade wooden units are gone and just the bed remains.

    Done most of the L90D paint job and its rather pleasing.

    Now the old 'lino' floor has to go as its looking rough and I don't want a brown/orange floor.

    Clearly the PO used a ton of glue to stick the lino down to the ply floor, its a pain to remove and even with care some of the ply surface is peeling off.

    But good to get rid of it and the ply is wet and black in places along the walk through area so water has got in and travelled down to the wet area. The van is on the driveway, nose down.

    When the lino is out, I have to decide what new flooring to have and I would like some advice please.

    What are my options and do I really need to glue it down.

    Re the damaged ply surface, could I just use wood filler and sand to an even finish?

    Also do folks seal around the floor edges to prevent water getting to the ply? If yes, what sealant is best.
     
    scrooge95 likes this.
  2. matty

    matty Supporter

    9C29F6BC-F978-41C8-A615-E2EEC87A76C4.jpeg I used thin water resistant ply then stuck cork floor tiles on top for that 70s look
     
  3. Carpet is the future ....

    Sent from my SM-G960F using Tapatalk
     
  4. mikedjames

    mikedjames Supporter

    If the ply was WBP or marine ply then it probably would not have come apart as you peeled the vinyl.

    Having gone that far I would lift it because wet ply touching vaguely painted metal equals a strong chance of rot.

    Throw it all away, refinish, repaint metal, fit Celotex then WBP ply . Varnish the new ply or use a carpet like Flotex which has a waterproof backing.. .
     
    scrooge95, Merlin Cat and mgbman like this.
  5. matty

    matty Supporter

    One tip don’t make it too thick or the door strip and sliding door will interfere
     
    mikedjames, Merlin Cat and mgbman like this.
  6. Old lino now removed. Horrible stuff, its hard, brittle and hessian backed. Glad to get rid of it.

    Working inside the van, raining outside, water is dripping in through two of the side windows and clearly the seals are not doing their job. The seals do not seem to be closing against the glass properly and the corners have some wrinkling.

    That would explain the wet patches in the ply floor, gap between ply and surrounding metal would allow water penetration.

    So looks like I am up for some window surround repairs and new seals, anyone done this and where do I get the best quality seals. Looks to me the existing seals were the wrong size as the gap for the glass looks too big. So its probably let water in for some time.

    The old ply is screwed down with allen key hex screws which could be interesting.
     
    Merlin Cat likes this.
  7. I used vinyl sheet in black and white square pattern.
    It's loose laid , the cupboard s and bed frame are on top of it
     
    scrooge95 and mgbman like this.
  8. I redid mine in the lock-together vinyl flooring, stuck down over old vinyl tile strips which had started to lift. Only issue was having to trim the aluminium floor trim, as the whole lot had become about 5mm too thick.

    Sealed around the edges with black silicone mastic.

    Looks super, really pleased with it :thumbsup:

    a floor 2 6s.jpg
     
  9. Dubs

    Dubs Sponsor supporter extraordinaire

    Schofields do decent seals. (Assume you have factory fitted windows, rather than converted van windows)
     

  10. is that the famous fence in the background.
     
    SweeneyTodd and Merlin Cat like this.
  11. Lol. Nope, just some old panels destined for the dump.
     
    S1mon likes this.
  12. Its a panel van with cut out windows. Anyway YouTube has come up trumps and I just found this clip from our friends at Combe Valley Campers.
     
    Merlin Cat, snotty and Dubs like this.
  13. mikedjames

    mikedjames Supporter

    At least Allen key hex screws provide ready made guides for drilling the heads off...


    If you are repairing metal then it might be worth checking you can get seals for exactly the same shaped holes that you are repairing. In case of creative thinking e..g. you have windows fitted from some other convenient (at the time) donor.
     
    Last edited: Oct 26, 2019
    Merlin Cat and mgbman like this.
  14. scrooge95

    scrooge95 Moderator and piggy bank keeper

    Black and white squares in Lino for me, on top of ply. The lino is stuck down with Lino tape, supplied by our local carpet fitters: apparently it comes back up easier than just regular glue.

    Do the job properly if you’ve got all winter to do it.

    And post some pictures.... I may have missed them, but in all my time on here, I’ve not seen a photo of your van @mgbman !
    Good luck with the resto :)
     
    Last edited: Oct 26, 2019
  15. Norris

    Norris Supporter

    I'd spend some time digging the muck out of the heads with a pin. The deeper you can get your Allen key to sit, the more successful you are likely to be :)
     
    mgbman likes this.

Share This Page